We do have A-frame trailer tongue toolboxes that are made in the USA, though the MaxxTow MaxxHaul Trailer Tongue Toolbox is made in China.
Like you mentioned, the RC Manufacturing toolboxes are made in the USA and are a very high quality toolbox. It has a locking handle to protect your tools, a weatherproof seal to keep them dry, and a gas strut that keeps the lid open while you find what you need so you don't have to hold it up. These A-frame toolboxes are available in black or silver... view full answer...
The RC Industries # UB1818-48 body of the box is made from 14 gauge steel, plus the door itself is made from 2 separate 14 gauge steel panels, for added durability. This box weighs in at 134-lbs and is manufactured in the USA. It sounds like this is going to be the heavy duty box that you're looking for! view full answer...
The Firestone air compressors such as # F9377 can handle typical moisture like what might splash up from the road when driving in the rain. But it is not designed to be submerged under water. For something to be waterproof it has to be able to be submerged under water for a certain amount of time and not let any water in.
It will be perfectly fine under your truck so long as you aren't planning on driving into any deep bodies of water! That is why Firestone makes a mount bracket, # F2530,... view full answer...
I spoke with my contact and B&W and the Custom Headache Rack # BWPUCP7500WA is made of 10 gauge steel except for the flat plates that attach to the bed sides. Those are 7 gauge.
This rack is not tested with toolboxes or tonneau covers so it is difficult to determine if it will work in conjunction with those items. It likely will not work if the tonneau cover blocks the lip in the inner part of the bed sides. view full answer...
I've linked an install video of the EcoHitch, part # 306-X7601, being installed on a 2016 Subaru Outback for you. The tools you need are:
Phillips and flat head screwdrivers
Ratchet with 10 mm socket
Trim Remover, part # ALL648544
Mallet
Utility Knife
Tape Measure
Grease pencil
Straight edge
Torque Wrench, part # ALL644044 view full answer...
The Telescoping Lug Wrench w/ Reversible Sockets # LW405 made by Redneck Trailer Supplies, is manufactured in Springfield Missouri, since 1979. view full answer...
The Underbody Truck or Trailer Toolbox, 36x18x18, item # UB1818-36, is constructed of minimum 14 gauge steel and in some places uses 13 gauge steel for strength. These boxes are manufactured in the U.S.A. view full answer...
The mounting brackets for the Wheel Masters Level Master Trailer Bubble Level with 5th Wheel Pin Box Mounting Bracket # WM6780 are made out of UV-protected plastic. The plastic is really durable though, and is designed to last, so it isn't going to just break apart, and won't corrode like a metal bracket would.
I have added a link below to a video review for you to check out as well of the Wheel Masters Level Master Trailer Bubble Level with 5th Wheel Pin Box Mounting Bracket # WM6780. view full answer...
The 7/8" Wide Trailer Coupler Latch Lock # 2878DAT is made of hardened steel.
As far as how easy it is to defeat, ultimately any lock can be defeated given enough time and the right tools. Since there is no gauge of how "breakeable" a specific lock is, we recommend making your setup look intimidating to deter would-be thieves.
If you are wanting to deter theft of your trailer when it is coupled then the Bulldog # BD580404 is a great option because it has a coupler lock and a ball mount... view full answer...
Aluminum A-Frame Trailer Tongue Toolbox Item # 350970 is weather resistant but not waterproof. For something to be considered waterproof it has to be able to be submerged under water for a certain period of time and not let water in. None of the toolboxes are waterproof but as far as keeping out rain they can do that just fine. view full answer...
The trailer hitch with the most capacity is the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 66" Wide # C13704 which has a towing capacity of 5,000 lbs and tongue weight capacity of 500 lbs. This will work on box frames, C-channel frames, or I-beam frames that are between 22" and 66" wide.
I have added a link to a video review of this hitch for you to check out as well. view full answer...
There are a few more products you would need to complete a 16 foot awning with part # LCV000231520. The material is 500 x 500 fabric denier at 13.5 ounces per square yard of vinyl/woven acrylic material.
You will need the Solera Manual Pull Style Awning Drive Head # LC271181
Solera Manual Pull Style Awning Idler Head # LC272397
Solera Rollbar Only For 16' White Awning # LC260560357
Solera Manual Awning Pull Strap # LC292794
Solera 63" Short Awning Support Arm # LC97UD
We don't have pictures... view full answer...
I found an online diagram for the fuse box of your 2015 Ford F-350 and according to it the trailer running light fuse is in the 26 position and takes a 30 amp fuse. It's labeled as trailer tow park lamps which may be why it was harder to track down. view full answer...
If your 2015 Chevrolet Equinox has a factory tow package, there should be a trailer connector at the rear of the vehicle, behind the rear bumper. The connector could also be inside a black box that is mounted under the vehicle. If this is present, then your Equinox almost definitely has a factory tow package.
Another way to be sure is to simply take your VIN number to a local Chevrolet dealer and they will be able to tell you exactly what was installed in the factory for your vehicle. view full answer...
If you got something like this Adapter 7 Pole to 4 Pole with Tester # 47345 you will be able to convert your 7 pole to the 4 pole you need to power your light # CR-007G, you can also test to see if everything is working. If everything is, I think you may have an issue with your wiring with your factory 4 pole. You may also want to check your fuse box for a blown fuse. Also try to check your factory wire connection under your truck bed. view full answer...
The Stromberg Carlson 4000 Series # VGD-10-4000 weighs roughly 32-lbs.
It should be noted that this tailgate isn't necessarily going to increase what the truck's payload much, if at all, but they're instead designed to reduce the damage that might otherwise occur when towing a 5th wheel trailer with a pin box that hangs close to the tailgate. These tailgates also reduce drag that ultimately will help improve gas mileage. view full answer...
The Curt 5th wheel hitches like # C16530-16017 are made overseas in Asia with steel from that region, but they are tested to meet US standards. Unless you are using a Sidewinder or have a Revolution pin box, I highly recommend you use a sliding 5th wheel hitch like # C16530-16020 or the B&W Companion Slider # BWRVK3370 which is made in the USA.
Reese makes an adapter for the OEM Underbed Rails # RP30156, to allow the use of standard sliding hitches with the factory puck system, which... view full answer...
Yakima racks are made in either Taiwan or China. The cargo boxes are made in the USA in Southern California.
All of the Thule 4 bike racks are made in the U.S.A., but there are no Thule 4-bike racks designed for campers that can withstand the extra torque. view full answer...
You should have no problem using the Convert-A-Ball Gooseneck Coupler Adapter, # CAB-C5G, on a 1,200 mile trip as long as the gross weight of your trailer remains under 20,000 lbs and the pin weight is under 4,000 lbs. We had one customer comment that he has been using his adapter for over 20,000 miles and it is still working great.
The only note I would add to this adapter is that there will be a noticeable difference in the ride quality if you are used to towing with a fifth wheel hitch.... view full answer...
Go To Results